shear plane

In addition, the crystals tend to have their slip plane parallel to the shear plane and slip direction parallel to the shear direction during the dynamic deformation.

同时，变形过程中晶体的滑移面趋向于平行剪切面，滑移方向平行剪切方向。

Study of Relationship between Chip Crimp and Shear Plane Shapes

切屑卷曲与剪切面形状之间关系的研究

A method is presented, by which the plane strain state on the earth's surface can be obtained with the combination of tidal line strain data and the tidal shear strain can be simulated numerically.

提出了由潮汐线应变的组合观测资料获取地表平面应变状态和对潮汐剪切应变进行数值模拟的方法。

The paper proposes a new method for calculating shear plane area based upon a new oblique cutting model with double edge.

根据新的斜角非自由切削模型，本文提出了新的剪切面积计算方法。

The experimental results proved that ( 1) there is an additional cyclic strain hardening effect caused by non-proportional loading, and ( 2) the relative orientation between maximum shear plane and free surface plays significant role on fatigue life.

非比例加载引起的附加循环硬化；（2）最大剪切平面与自由表面相对取向对疲劳寿命的影响；

Effects of Shear Plane Boundary Condition on Depth of Surface Work hardening

剪切面边界条件对工件表面层加工硬化深度的影响

And the formula for angle of shear plane is modified by chip shortening coefficient.

并通过切屑变形系数来修正模型中的剪切角计算公式。

The principal shear fracture plane of rock under compression shear state is to propagate along the upper boundary of the fracture zone.

岩石压剪主剪断面沿该破裂区上部边界扩展。

EVALUATION OF ELASTIC AND ULTIMATE FLEXURAL STRENGTH IN DESIGN OF PARTIALLY COMPOSITE BEAM Determination of the shear plane quantity of shearing force bolt connection

部分剪切连接组合梁弹性刚度和极限强度的计算剪力螺栓连接剪切面数目的确定

A New Method for Calculation Shear Plane Area in Oblique Cutting with Double Edge

新的斜角非自由切削剪切面积计算方法

Firstly, probing the medium with a time-harmonic homogeneous plane wave gives the Christoffel equation. Then the formulas for slowness and complex velocities of the longitudinal wave and the slow and quick shear waves may be obtained from Christoffel equation.

使用平面均匀简谐波的方法，得到了Christoffel方程，利用此方程推导出纵波及快、慢横波的慢度和复速度方程。

It is obvious by strain measure, petrofabric analysis, shear displacement amount counting and isotopic dating that ① the ductile shear zone's deformation belongs to plane simple-shear strain, and later the deformation translates into extensional strain.

应变测量、岩组分析、剪切位移量计算、同位素测年等定量分析表明：①以平面单剪应变为主，稍晚向伸长应变转化；

Seismic precursor variation and residual vector in tidal observations of line strain, shear strain and plane strain

地表潮汐线应变、剪应变与面应变观测的残差矢量及其震兆变化

In this paper, taking an crack extending with constant velocity On the longitudinal plane as the example, the author discusses the relationship between extending velocity and shear stress.

本文以纵向平面上断裂按常速度扩展为例，讨论了滑动速度与剪切应力的关系；

Determination of the shear plane quantity of shearing force bolt connection

剪力螺栓连接剪切面数目的确定

The analysis covers plane strain, plane stress and anti-plane strain shear cases.

分析包括了平面应变 、 面应力和出平面应变剪切三种情况.

It is justified that the maximum cyclic shear effect plane of the specimens in triaxial liquefaction test and-simple shea'r liquefaction test and of soil elements under general plane strain condition can only be determined by static stress components and is undependent on cyclic stress.

对于三轴液化试验、简切液化试验的受力条件和平面应变状态下土单元的受力条件，证明了最大往返剪切作用面的位置只由静力有效应力分量来确定而与往返应力无关。